Discovering Plumbing Basics is Essential When Installing a Bathtub
Discovering Plumbing Basics is Essential When Installing a Bathtub
Blog Article
They are making several good pointers on A Step-by-Step Guide to Installing a Bathtub as a whole in the content down the page.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Setting up a tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, and also often, tiling abilities. Changing an old bathtub with a new one is also a reasonably challenging job. If the old tub is conveniently accessible, the task can move quickly; if you have to open up a wall surface to remove the old bathtub and also position the new bathtub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as set in the brand-new one. Ensure you have certified on your own for the task and are comfortable trying it. Instead of hiring a professional to take control of a halfway-completed project, it is better to take into consideration using one prior to you begin. Possibilities are you might require a specialist plumber to make tube links.
This article will assist you install a brand-new tub in your shower room if you have actually currently bought a brand-new tub and also don't require to alter the plan of your previous water supply pipelines.
Your tools and material list must consist of the following:
Getting ready for the Setup
First of all, the supporting frame supplied with the bathroom must be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to avoid stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath should currently prepare to be suited its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be quite troublesome as a result of the limited accessibility that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a fabric prepared for the staying water that will certainly come from the pipelines. When the supply pipelines have actually been eliminated, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing compound.
Before going on to fit the new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Installing the Bathtub
Using the two wood boards under its feet, position the bath tub in the needed placement. The wooden boards are handy in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the bath tub till the spirit level checks out level.
To mount taps, fit all-time low of the outermost adaptable faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the supply of water as well as inspect all joints and brand-new pipework for leaks as well as tighten them if needed. Fill the bath tub and also examine the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bath paneling as explained in the supplier's user's manual. Tiling and securing around the tub must wait until the tub has actually been used a minimum of when as this will certainly settle it into its final placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin guaranteeing that the washers are in area between the tap and also the sink. Secure the tap in place with the maker provided backnut. When the tap is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical faucet connectors. The former kind must be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break a rigid seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, leading to complications with moisture as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to always load the bath tub with water before securing, to permit the motion experienced when the tub remains in use. The sealant can crack rather very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly available on the marketplace. It is a good idea to fit the floor tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that report about Installing A Bathtub from someone on a different website. Sharing is good. Helping people is fun. Thank you for going through it.
Schedule Now Report this page